Title: Stiffener Jumping for Unitized Stitched Composite Preform Manufacturing

Authors: Andrew E. Lovejoy

DOI: 10.33599/nasampe/c.22.0012

Abstract: A single-sided stitching head is used to assemble unitized three-dimensional preforms using the NASA Langley Research Center (LaRC) Integrated Structural Assembly of Advanced Composites (ISAAC) robotic manufacturing system. Typically, assembly of a preform includes a “skin” that is stiffened by stiffener elements stitched to the skin. The single-sided stitching head has two needles that pass through the preform from the same side to form the stitch, typically from the smooth outer surface so the needles penetrate through the preform towards the stiffener side. The single-sided head cannot stitch across stiffening elements (e.g., stringer, frame, integral cap, etc.) because the needles would penetrate into the stiffener web, which would not allow the stitch form because the thread movement would be impeded. As a result, stitching seams cannot cross stiffening elements, and therefore are very short and must remain in the skin/flange connections within the space between the stiffening element webs. Each short segment requires a stop and cut process that takes a significant amount of time. A stiffener jumping stitching method was developed that eliminates the need to cut and restart seams when encountering a stiffener, thus providing a long, continuous seam with a significant reduction in stitching time by eliminating cutting operations and associated excess thread end trimming. This stiffener jumping process places what could be considered a very long stitch that bridges the stiffener to connect the end of one segment of the seam with the beginning of the next segment of the seam to provide a longer continuous seam. As a result, all intermediate thread cuts that would be done at the end of each individual segment of the seam are eliminated, with only a single cut at the end of the seam. The process and programming requirements for carrying out the stiffener jumping stitching approach are presented in this paper. Using the presented stiffener jumping approach to produce the long continuous seams, the stitching time for a representative commercial transport unitized stiffened wing cover panel can possibly be reduced by at least 25 percent.

References: 1. M. B. Dow and H. B. Dexter, “Development of Stitched, Braided and Woven Composite Structures in the ACT Program and at Langley Research Center (1985 to 1997),” NASA TP-97-206234. 2. D. C. Jegley, H. G. Bush, and A. E. Lovejoy, “Structural Response and Failure of a Full-Scale Stitched Graphite–Epoxy Wing,” Journal of Aircraft, Vol. 40, No. 6, November–December 2003, pp. 1192-1199. 3. M. Rouse, D. C. Jegley, D. M. McGowan, H. G. Bush, and W. A. Waters, “Utilization of the Building-Block-Approach in Structural Mechanics Research,” 46th AIAA/ASME/ ASCE/AHS/ASC Structures, Structural Dynamics & Materials Conference, 18 - 21 April 2005, Austin, Texas. (Available as AIAA Paper 2005-1874.) 4. M. Karal, “AST Composite Wing Program – Executive Summary,” NASA CR-2001-210650. 5. K. Gould, A. E. Lovejoy, D. C. Jegley, A. L. Neal, K. A. Linton, A. C. Bergan, and J. G. Bakuckas, Jr., “Nonlinear Analysis and Experimental Behavior of a Curved Unitized Stitched Panel,” Journal of Aircraft, Vol. 52, No. 2, March–April 2015, pp. 628-637. 6. D. C. Jegley, “Structural Efficiency and Behavior of Pristine and Notched Stitched Structure,” presented at the annual SAMPE meeting October 17-20, 2011. 7. N. Yovanof and D. C. Jegley, “Compressive Behavior of Frame-Stiffened Composite Panels,” presented at the 52nd AIAA Structures Dynamics and Materials Conference, April, 2011. 8. D. C. Jegley, “Behavior of Frame-Stiffened Composite Panels with Damage,” presented at the 54th AIAA Structures, Structural Dynamics, and Materials Conference, April, 2013. 9. A. Allen and A. Przekop. 2012. “Vibroacoustic Characterization of a New Hybrid Wing-Body Fuselage Concept,” presented at the INTER-NOISE 2012 Conference, August, 2012. 10. A. E. Lovejoy, M. Rouse, K. Linton, and V. Li, “Pressure Testing of a Minimum Gauge PRSEUS Panel,” presented at the 52nd AIAA Structures Dynamics and Materials Conference, April, 2011. 11. N. Yovanof, A. E. Lovejoy, J. Baraja, and K. Gould, “Design Analysis and Testing of a PRSEUS Pressure Cube to Investigate Assembly Joints,” Aircraft Airworthiness and Sustainment Conference, April, 2012. 12. A. Przekop, “Repair Concepts as Design Constraints of a Stiffened Composite PRSEUS Panel,” presented at the 53rd AIAA/ASME/ASCE/AHS/ASC Structures, Structural Dynamics and Materials Conference, May, 2012. 13. A. Przekop, D. C. Jegley, M. Rouse, and A. E. Lovejoy, “Analysis and Testing of a Metallic Repair Applicable to Pressurized Composite Aircraft Structure,” Presented at the Society for the Advancement of Material and Process Engineering (SAMPE) Technical Conference, June, 2014. 14. D. C. Jegley, “Experimental Behavior of Fatigued Single Stiffener PRSEUS Specimens,” NASA-TM-2009-215955. 15. P. J. Thrash, “Manufacturing of a Stitched Resin Infused Fuselage Test Article,” Presented at the Society for the Advancement of Material and Process Engineering (SAMPE) Fall Technical Conference, Orlando FL, October, 2014. 16. NASA ISAAC Fact Sheet, FS-2021-10-307-LaRC, 2021. 17. A. E. Lovejoy and D. C. Jegley, “Stitching Path Control to Enable Stitched Composites with Three-Dimensional Stitch Paths,” SAMPE Journal, to be published June–August, 2022.

Conference: CAMX 2022

Publication Date: 2022/10/17

SKU: TP22-0000000012

Pages: 16

Price: $32.00