Title: CHALLENGES IN AM THERMOSET CONTINUOUSLY-REINFORCED COMPOSITES

Authors: Jevan Furmanski, Andrew Abbott, G. P. Tandon, Mark Flores, Philip Barnett, Marco Salviato, Jeffery Baur, Dennis Butcher

DOI: 10.33599/nasampe/s.23.0141

Abstract: Continuously-reinforced composite additive manufacturing (CC-AM) is set to revolutionize the manufacturing and design of complex high-strength, low-weight structures. Longitudinal tensile strengths of CC-AM have been reported exceeding 1500 MPa with minimal porosity, making this system available for structural applications. However, there remain a number of morphological non-idealities that are unique to the CC-AM process that challenge the performance of a complex AM build. These can be categorized into material non-idealities (fiber clustering, resin-rich zones, matrix quality) and topological constraint non-idealities (joint design constraints, minimum path radius, tow cuts). Furthermore, for UV snap-cured carbon fiber CC-AM, limited penetration of the incident UV through the carbon fiber tow presents a challenge to optimal in-situ curing. The present work lays out these challenges, with specific case examples for material built with the CF3D system (Continuous Composites Inc.) using T-1100 12K carbon fiber tows and a UV snap curing acrylate resin. Most of the issues highlighted are inherent to CC-AM, so the recommendations for future development to mitigate the various non-idealities are expected to translate to other CC-AM technologies, such as those using a thermoplastic polymer.

References: [1] Ngo, T.D., Kashani, A., Imbalzano, G, Nguyen, K.T.Q, Hui, D. “Additive manufacturing (3D printing): A review of materials, methods, applications and challenges,” Comp Part B (143): 172-196. 2018. [2] Werken N van de, “Additively manufactured continuous carbon fiber thermoplastic composites for high-performance applications.” Doctoral dissertation, University of New Mexico. 2019. [3] Matsuzaki R, Ueda M, Namiki M, et al. “Three-dimensional printing of continuous-fiber composites by in-nozzle impregnation,” Sci Rep (6): 1–7. 2016. [4] Baur, J.W., Abbott, A.C., Barnett, P., Tandon, G.P., Furmanski, J, Stranberg, N.A., Alvarado, T.B., 2022. Accepted for publication by J Comp Mat. [5] Ming Y, Duan Y, Wang B, et al., “A novel route to fabricate high-performance 3D printed continuous fiber-reinforced thermosetting polymer composites,” Materials (Basel) (12). 2019. [6] Hao W, Liu Y, Zhou H, et al., “Preparation and characterization of 3D printed continuous carbon fiber reinforced thermosetting composites,” Polym Test (65): 29–34. 2018. [7] Der Klift F Van, Koga Y, Todoroki A, et al., “3D Printing of Continuous Carbon Fibre Reinforced Thermo-Plastic (CFRTP) Tensile Test Specimens,” Open J Compos Mater (6): 18–27. 2016. [8] Toray Composite Materials America. T1100G intermediate modulus carbon fiber datasheet. Toray Composite Materials America, Inc. [9] Bendsoe, M.P., and Sigmund, O. 2002. Topology Optimization, 2ed. Springer. [10] Anastasio, R., Maassen, E.E.L, Cardinaels, R., Peters, G.W.M., van Breemen, L.C.A., “Thin film mechanical characterization of UV-curing acrylate systems,” Polymer (150): 84-94. 2018. [11] Karam G.N., “Effect of fibre volume on tensile properties of real unidirectional fibre-reinforced composites,” Composites (22): 84–88. 1991.

Conference: SAMPE 2023

Publication Date: 2023/04/17

SKU: TP23-0000000141

Pages: 12

Price: $24.00