Title: Increasing Deposition Rates and Quality of Additively Manufactured High Fiber Fraction Continuous Fiber Composites

Authors: Femi Ibitoye, Donald Radford

DOI: 10.33599/nasampe/s.25.0131

Abstract: A previous published study performed by the authors had already shown the application of commingled yarn in a direct digital manufacturing approach to additively manufacture composites averaging 50 % fiber volume fraction, but quality of parts diminished when deposition speed was increased. In order to employ this processing approach in a commercial setting, it is necessary to maintain composite quality while at the same time increasing deposition rates. In this current effort, two process modifications are used to address this challenge: increasing length of heated zone and increasing number of tows. Here, samples were manufactured at 3 different levels of print speeds, 3 different heated zone lengths and 2 levels of tow count. Matrix pyrolysis was performed to evaluate composite quality by determination of fiber and void fractions. Experimental results show a significant improvement in quality when at a set baseline deposition rate, void fraction was reduced by about 70 % with increased heated zone length. Further, doubling of the deposition rate still yielded a 23 % drop in void fraction compared to baseline when heated zone length was increased.

References: [1] L. Yan, Z. C. Chen, Y. Shi, and R. Mo, “An accurate approach to roller path generation for robotic fibre placement of free-form surface composites,” Robot. Comput.-Integr. Manuf., vol. 30, no. 3, pp. 277–286, Jun. 2014, doi: 10.1016/j.rcim.2013.10.007. [2] D. H.-J. A. Lukaszewicz, C. Ward, and K. D. Potter, “The engineering aspects of automated prepreg layup: History, present and future,” Compos. Part B Eng., vol. 43, no. 3, pp. 9971009, Apr. 2012, doi: 10.1016/j.compositesb.2011.12.003. [3] K. Croft, L. Lessard, D. Pasini, M. Hojjati, J. Chen, and A. Yousefpour, “Experimental study of the effect of automated fiber placement induced defects on performance of composite laminates,” Compos. Part Appl. Sci. Manuf., vol. 42, no. 5, pp. 484–491, May 2011, doi: 10.1016/j.compositesa.2011.01.007. [4] K. Fayazbakhsh, M. Arian Nik, D. Pasini, and L. Lessard, “Defect layer method to capture effect of gaps and overlaps in variable stiffness laminates made by Automated Fiber Placement,” Compos. Struct., 10.1016/j.compstruct.2012.10.031. vol. 97, pp. 245–251, Mar. 2013, doi: [5] M. Lan, D. Cartié, P. Davies, and C. Baley, “Influence of embedded gap and overlap fiber placement defects on the microstructure and shear and compression properties of carbonepoxy laminates,” Compos. Part Appl. Sci. Manuf., vol. 82, pp. 198–207, Mar. 2016, doi: 10.1016/j.compositesa.2015.12.007. [6] R. Harik, C. Saidy, S. J. Williams, Z. Gurdal, and B. Grimsley, “AUTOMATED FIBER PLACEMENT DEFECT IDENTITY CARDS: CAUSE, ANTICIPATION, EXISTENCE, SIGNIFICANCE, AND PROGRESSION”. [7] V. C. Jamora, V. Rauch, S. G. Kravchenko, and O. G. Kravchenko, “Effect of Resin Bleed Out on Compaction Behavior of the Fiber Tow Gap Region during Automated Fiber Placement Manufacturing,” Polymers, vol. 16, no. 1, p. 31, Dec. 2023, doi: 10.3390/polym16010031. [8] V. C. C. Jamora, O. Kravchenko, and S. Kravchenko, “Process Modeling of a Multidirectional Laminate with Multiple Embedded Staggered Tow Gaps,” in AIAA SCITECH 2023 Forum, National Harbor, MD & Online: American Institute of Aeronautics and Astronautics, Jan. 2023. doi: 10.2514/6.2023-0523. [9] A. Trochez, V. C. Jamora, R. Larson, K. C. Wu, D. Ghosh, and O. G. Kravchenko, “Effects of automated fiber placement defects on high strain rate compressive response in advanced thermosetting composites,” J. Compos. Mater., vol. 55, no. 30, pp. 4549–4562, Dec. 2021, doi: 10.1177/00219983211042073. [10] H. Ghayoor, C. C. Marsden, S. V. Hoa, and A. R. Melro, “Numerical analysis of resinrich areas and their effects on failure initiation of composites,” Compos. Part Appl. Sci. Manuf., vol. 117, pp. 125–133, Feb. 2019, doi: 10.1016/j.compositesa.2018.11.016. [11] A. S. Mahmood, J. Summerscales, and M. N. James, “Resin-Rich Volumes (RRV) and the Performance of Fibre-Reinforced Composites: A Review,” J. Compos. Sci., vol. 6, no. 2, p. 53, Feb. 2022, doi: 10.3390/jcs6020053. [12] H. Ahmadian, M. Yang, and S. Soghrati, “Effect of resin-rich zones on the failure response of carbon fiber reinforced polymers,” Int. J. Solids Struct., vol. 188–189, pp. 74–87, Apr. 2020, doi: 10.1016/j.ijsolstr.2019.10.004. [13] D. Del Rossi, V. Cadran, P. Thakur, M. Palardy-Sim, M. Lapalme, and L. Lessard, “Experimental investigation of the effect of half gap/half overlap defects on the strength of composite structures fabricated using automated fibre placement (AFP),” Compos. Part Appl. Sci. Manuf., vol. 150, p. 106610, Nov. 2021, doi: 10.1016/j.compositesa.2021.106610. [14] A. Marouene, P. Legay, and R. Boukhili, “Experimental and numerical investigation on the open-hole compressive strength of AFP composites containing gaps and overlaps,” J. Compos. Mater., vol. 51, no. 26, pp. 3631–3646, Nov. 2017, doi: 10.1177/0021998317690917. [15] C. Zhao, J. Xiao, Y. Li, Q. Chu, T. Xu, and B. Wang, “An Experimental Study of the Influence of in-Plane Fiber Waviness on Unidirectional Laminates Tensile Properties,” Appl. Compos. Mater., vol. 24, no. 6, pp. 1321–1337, Dec. 2017, doi: 10.1007/s10443-017-9590-z. [16] L. Maragoni, G. Modenato, N. De Rossi, L. Vescovi, and M. Quaresimin, “Effect of fibre waviness on the compressive fatigue behavior of woven carbon/epoxy laminates,” Compos. Part B Eng., vol. 199, p. 108282, Oct. 2020, doi: 10.1016/j.compositesb.2020.108282. [17] R. D. R. Sitohang, W. J. B. Grouve, L. L. Warnet, and R. Akkerman, “Effect of in-plane fiber waviness defects on the compressive properties of quasi-isotropic thermoplastic composites,” Compos. Struct., vol. 272, p. 114166, Sep. 2021, doi: 10.1016/j.compstruct.2021.114166. [18] A. Altmann, P. Gesell, and K. Drechsler, “Strength prediction of ply waviness in composite materials considering matrix dominated effects,” Compos. Struct., vol. 127, pp. 51–59, Sep. 2015, doi: 10.1016/j.compstruct.2015.02.024. [19] R. D. R. Sitohang, W. J. B. Grouve, L. L. Warnet, S. Wijskamp, and R. Akkerman, “The relation between in-plane fiber waviness severity and first ply failure in thermoplastic composite laminates,” Compos. Struct., vol. 289, p. 115374, Jun. 2022, doi: 10.1016/j.compstruct.2022.115374. [20] J. Wang, K. D. Potter, and J. Etches, “Experimental investigation and characterisation techniques of compressive fatigue failure of composites with fibre waviness at ply drops,” Compos. Struct., vol. 100, pp. 398–403, Jun. 2013, doi: 10.1016/j.compstruct.2013.01.010. [21] N. Bakhshi and M. Hojjati, “An experimental and simulative study on the defects appeared during tow steering in automated fiber placement,” Compos. Part Appl. Sci. Manuf., vol. 113, pp. 122–131, Oct. 2018, doi: 10.1016/j.compositesa.2018.07.031. [22] S. Wang, M. Ç. Akbolat, K. B. Katnam, Z. Zou, P. Potluri, and J. Taylor, “On the interlaminar fracture behavior of carbon/epoxy laminates interleaved with fiber‐hybrid nonwoven veils,” Polym. Compos., vol. 45, no. 4, pp. 3315–3326, Mar. 2024, doi: 10.1002/pc.27992. [23] G. Jacobsen, “Mechanical Characterization of Stretch Broken Carbon Fiber Materials— IM7 Fiber in 8552 Resin”. [24] F. C. Campbell, Manfacturing processes for advanced composites. New York: Elsevier, 2004. [25] B. S. Hayes and L. M. Gammon, Optical Microscopy of Fiber-Reinforced Composites. ASM International, 2010. doi: 10.31399/asm.tb.omfrc.9781627083492.

Conference: SAMPE 2025

Publication Date: 2025/05/19

SKU: TP25-0000000131

Pages: 13

Price: $26.00